gnadmin | GN Decanter Centrifuge

Drilling cuttings decanter centrifuge at the jobsite

GN solids control already offered over 250 models drilling cuttings decanter centrifuge around the world, here is a photo of GNLW363VFD decanter centrifuge at the jobsite. Besides of the decanter centrifuge, this client also utilized our screw conveyor to gather the drilling cuttings and transfer them. Screw conveyor is specifically utilized for drilling cuttings moving among the drilling waste management system, particularly for the drilling cuttings with fewer liquids, the performance of transfer is demonstrated much better than other moving techniques.

Probably the most important feature of the screw conveyor quality is that the bearings and screw propeller; it’s frequently used flat or in a slight incline to transfer the types of materials. GN always choose renowned brand bearings for such essential components, so we provide various options of screw material as customer’s requirement, even the screw conveyor length also can be customized, we’ve various sections with every section 12ft length.

Normally our client can make a higher and adjustable frame in your area for their only project; they will put our decanter centrifuge around the frame. Our decanter centrifuge can be used the programs below:

1 water drilling liquids dewatering centrifuge

2 barite recovery centrifuge in solids control system

3 decanter centrifuge for top gravity and occasional gravity solids

4 drilling cuttings treatment system

5 waste water treatment

The most crucial problem within the jobsite operation is maintenance, with higher and proper maintenance; the decanter centrifuge can function perfectly. Here is the instructions ought to be compensated more attention for that centrifuge operation.

1 cleaning after each time operation by water or drilling liquids

2 lube based on GN recommend lube chart

3 tighten the security guard belt before shipment, and take away it before start

GN professional engineer will fly for your jobsite to train your operator that helps for brand spanking new commissioning service.

Related Arciels:

Soil and Liquid mixing tank

GN Solids Control is China leading manufacturer on mud solids control and drilling waste management system. They have experience on oily sludge separation. Recently, there are customers request V-bottom mud mixing tank for soil and oil liquid. The soil and oil liquid will go into the tank and they are mixed

The output line from the tank is a screw type (screw conveyor), so it can deliver the settled solid particles. And the height of the end of screw is 3 meter. Finally, there should be a liquid pump to transfer the liquid to other tanks or equipment.

V-bottom Screw + Shiftless conveyor

1) Solid/liquid mixture will be go into the v-bottom screw.

2) V-bottom screw and shiftless conveyor are put together and have sealing for no liquid leakage

3) Solid will be taken out from bottom screw – shiftless conveyor – and be discharged

4) Liquid will be pumping out from the top or making a hole at proper elevation

GN Solids control can provide tank and augers to meet the required function.

Below is a draft proposal made for customer’s reference.

1) Height of tank (including V-bottom) : 1.8 meter

2) Width of tank: 2 meter

3) Length of horizontal auger in tank : 24 feet long ( 7.315 meter)

4) Length of tilt auger: 24 feet long (7.315 meter), with tilting angle between auger and horizontal level 25 degrees.

Customer is satisfied with the proposal and mentioned more request. They want steam heating system for the mixing tank:

– Steam injection nozzles (in this case, 2 nozzles each side (total 4 nozzles) can be installed and the nozzle would be positioned 0.5m from bottom)

– Wired screen (5 cm) on the top where operator pour the soil into the tank.

Per customer request, GN Solids Modification V-bottom Screw conveyor:

1. Steam injection line and nozzles inside

– steam injection line is split to two lines which are inserted into the v-bottom screw tank.

– 3 injection nozzles from each pipeline inside of v-bottom tank

– steam injection pipeline: 2 inch diameter (see picture below)

– no need of mixer inside

The Introduction on the Drilling Liquids

Drilling liquids has become broadly utilized in oil, gas drilling along with other drilling mud system. Using the solids control equipment, the drilling liquids might be recycled many occasions for cost saving and atmosphere protection. This short article gives an easy introduction around the purpose of the drilling liquids.

What’s the purpose of the drilling liquids?

1. Eliminating bottom from the well our prime pressure drilling liquids get out of the drill bit would flush the foot of the well make no obstacles for drilling process.

2. Carry cuttings – the drilling liquids would go ahead and take drilling cuttings to the floor surface for mud cleaning process.

3. Balance formation pressure – because of the very deep drilling, the drill bit can experience different formations for example rock formation and ground water formation. The drilling liquids here performed to avoid the floor water stepping into the drilling well. This could safeguard the geological structure.

Besides, the drilling liquids may also function to awesome lower and lubricate drill bit, safeguard borehole wall and supply downhole energy.

To completely have the drilling liquids advantages, you will find several needs around the drilling liquids.

1. The drilling liquids should meet interest in drilling mud recycling

Drilling cycle request the drilling liquids low pump pressure (low fluid viscosity), excellent capability to carry cuttings (dynamic pressure is high), low beginning pump pressure (low static shear pressure), good lube performance, low friction (less solids contaminants)

2. Keep up with the stability of borehole

It’s asked for to make use of drilling liquids column to balance the development pressure. So when drill oil and gas layer, the drilling liquids can also be required to balance pressure from the oil and gas. That will request a reliable density from the drilling mud.

3. Oil and gas protection

After drilling oil and gas layer, drilling fluid contacts with oil and gas. To avoid drilling fluid harmful the oil and gas layer, the drilling liquids ought to be small filtration, thin mud cake, low solid content and occasional filtrate of hydration etc.

4. Safeguard the character atmosphere

Drilling fluid frequently consists of oil and oil, diesel oil and a lot of chemical agents. To be able to avoid the possible effect on character atmosphere, non-toxic, harmless drilling liquids ought to be used.

Centrifugal pump Mechanical seal

There mainly 3 sealing types for centrifugal pumps, like shearing pump, sand pump , slurry pump, etc…

1) Asbestos packing

2) Arid seal

3) Mechanical seal

Mechanical seal is the greatest and many costive sealing types. It’s reliable with an extended lifetime.

The fundamental meaning of Centrifugal pump Mechanical seal

Mechanical seal is the seal device for rotary machines. Like centrifugal pumps, centrifuges, reactor along with a compressor equipment. Since the transmission shaft goes through within the inside and outdoors from the equipment, so, the presence of a circumferential clearance between your shaft and also the equipment, equipment of medium leakage outwards with the gap, when the equipment within the pressure is gloomier compared to atmospheric pressure, air towards the equipment inside leakage, and for that reason it has to possess a package to avoid leakage from the shaft. Many seal species, because of mechanical seal has the benefits of little bit of leakage and lengthy service existence and so forth, so in present day world, mechanical seal is sealed within the primary shaft from the equipment. Mechanical seal can also be known as the face area seal, within the relevant standards from the condition is understood to be: “by a minimum of a set of finish faces vertical with respect towards the axis of rotation within the fluid pressure and also the elasticity of compensation organizations (or magnetic) device function and coordination of auxiliary closes to help keep integrating carefully relative sliding form to avoid fluid leakage.

Review of concepts on Centrifugal pump Mechanical seal

Mechanical seal is as simple as a set of or number around the vertical axis for finish face relative sliding within the fluid pressure and also the compensation mechanism of elastic (or magnetic) under the act of coupled with keep adhering auxiliary sealing and leakage potential to deal with seal device.

Common mechanical seal structure comprises an immobile ring (static ring) 1, rotating ring (dynamic ring) 2, 3 elastic components, a spring chair 4, fastening screw 5, a rotating ring auxiliary seal ring 6, and also the static ring auxiliary seal ring 8 along with other components, anti rotation pin 7 is bound around the cover 9 to avoid static the rotation from the ring.

Rotating ring and also the stationary ring is frequently may also based on when they have been the axial compensation capacity and it is known as the compensation loop or non compensation ring.

GN Mini Centrifuge

You might become complacent that the machine is big monster having a large footprint and high weight. It always gets people to feel gloomy when standing before an enormous machine. But consider the following picture, how cute it’s. It’s a small decanter centrifuge from GN decanter centrifuge products. With small footprint, you can easily remove and transport, additionally, it saves a great deal space for customers. Regarding its parameter, the mainly two is dealing with capacity and speed. GN small decanter centrifuge’s dealing with capacity or processing volume is 6 cubic meter each hour. And it is speed can achieve to some maximum round each minute. As well as for its primary feature that we will talk in next paragraph, it is usually utilized in core drilling.

GN mini decanter centrifuge using the model GNLW223 mainly occupied the next features.

1. small footprint for simple moving and narrow working space

2. One motor driven mode for the bowl and inside screw propeller. The motor drive the bowl using a belt lever with devices, the bowl has same rotation speed because the motor. Meanwhile, the style of gear unit helps make the input speed from the screw propeller is a lot less than the bowl ¨C the screw propeller can also be driven through the motor having a belt lever. Thus the presence of the differential speed results in the centrifuge working availability.

3. High typical accelerate to 4500 make the sufficient G pressure to split up the fine solids with size 2~5 microns.

4. Material of SS304 on bowl, screw conveyor and primary body and protection of tungsten carbide squirting welding is perfect for lessen the cost, but could satisfy the working demand well.

5. Both fixed speed and variable speed model can be obtained

GN Solids Control has approached with lots of clients from Canada in the industry of core drilling along with other mining drilling. To think about our prime requirement around the motor and control panel explosion proof standard, GN provides the Small centrifuge only mechanical part and also the customer may find the motor and control panel in your area. And GN has done such as this before.

http://gnsolidsamerica.nation2.com/index.php?page=1372521394_11